This repair manual covers Chevrolet Silverado and GMC pick-ups 1999-2006 including:
- Chevrolet Suburban and Tahoe 2000-2006
- GMC Yukon, Yukon XL, Sierra Denali and Yukon Denali 2000-2006
- Chevrolet Avalanche 2002-2006
- Chevrolet Silverado Classic 2007
- GMC Sierra Classic 2007
Covers both 2WD and 4WD versions.
Note: this manual DOES NOT include 1999 and 2000 C/K Classic, 1999 and 2000 Sierra Classic, diesel, 8.1L engine, CNG models, hybrids, models equipped with rear-wheel steering or heavy-duty model information.
Book Excerpt: 1999-2006 Chevrolet Silverado, GMC Sierra 2WD and 4WD Repair Manual
REPAIR OPERATIONS POSSIBLE WITH THE ENGINE IN THE VEHICLE
Many major repair operations can be accomplished without removing the engine from the vehicle.
TABLE of CONTENTS:
Clean the engine compartment and the exterior of the engine with some type of pressure washer before any work is done. A clean engine will make the job easier and will keep dirt out of the internal areas of the engine.
Depending on the components involved, it may be a good idea to remove the hood to improve access to the engine as repairs are performed (refer to Chapter 11 if necessary.)
If oil or coolant leaks develop, indicating a need for gasket or seal replacement, the repairs can generally be made with the engine in the vehicle. The oil pan gasket, the cylinder head gaskets, intake and exhaust manifold gaskets, timing chain cover gaskets and the crankshaft oil seal are all accessible with the engine in place.
Exterior engine components, such as the water pump, the starter motor, the alternator, the distributor and the fuel injection components, as well as the intake and exhaust manifolds, can be removed for repair with the engine in place.
Since the cylinder heads can be removed without removing the engine, valve component servicing can also be accomplished with the engine in the vehicle.
Replacement of, repairs to or inspection of the timing chain and sprockets and the oil pump are all possible with the engine in place.
In extreme cases caused by a lack of necessary equipment, repair or replacement of piston rings, pistons, connecting rods and rod bearings is possible with the engine in the vehicle. However, this practice is not recomended because of the cleaning and preparation work that must be done to the components involved.
About this manual | Introduction to the Chevrolet Silverado, Suburban, Tahoe and GMC Sierra, Yukon, Yukon XL, Sierra Denali, Yukon Denali | Vehicle identification numbers | Buying parts | Maintenance techniques, tools and working facilities | Jacking and towing | Booster battery (jump) starting | Automotive chemicals and lubricants | Conversion factors | Fraction/decimal/millimeter equivalents | Safety first! | Troubleshooting
- Tune-up and routine maintenance
- V6 engine
- V8 engine
- General engine overhaul procedures
- Cooling heating and air conditioning systems
- Fuel and exhaust systems
- Engine electrical systems
- Emissions and engine control systems
- Manual transmission
- Automatic transmission
- Transfer case
- Clutch and drivelines
- Suspension and steering systems
- Chassis electrical system
- Wiring diagrams
I purchased this manual to help me accomplish some repair items I needed to get done. I was unemployed at the time and could not afford the cost of a mechanic.
The manual helped me accomplish all the repairs I needed and then some. The service interval section is priceless and the photos and attention to detail is awesome. Even though I am not an electrician, I was able to install electric cooling fans with ease. The schematics are a great help and easy to read. They are also broken down into easy to find sections so you don?t have to spend so much time going through pages and pages of information. Thanks Motor Bookstore. I will be back.
andmdash;Greg Bowen. Atlanta, Georgia.
Subject: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006 Chevrolet Silverado, GMC service, maintenance, repair. ISBN-10: 1563926814 | ISBN-13: 9781563926815