Triumph Tiger Cub, Terrier, Super Cub, Bantam Cub Repair Manual 1952-1968

SKU: HYM414-968
Triumph Tiger Cub, Terrier Repair Shop Manual 1952-1968
Triumph Tiger Cub, Terrier Repair Shop Manual 1952-1968
MSRP: $39.95
Only $34.85
Free Shipping (US48)
In Stock
Item #: HYM414-968
-
+
Usually ships the next business day
Why Buy From Us?
  • Free Shipping
  • Veteran Owned
  • Secure Shopping
  • Satisfaction Guaranteed
Item Description

The 1952-1968 Triumph Tiger Cub, Terrier, Super Cub, Bantam Cub Repair Manual by Haynes, covers models indicated, including:

  • Triumph T15 Terrier, 1952-1956
  • Triumph T20 Tiger Cub, 1954-1966
  • Triumph T20C Tiger Cub Competition, 1956-1959
  • Triumph T20S Tiger Cub Sports, 1959-1960
  • Triumph T20T Tiger Cub Trials, 1960-1961
  • Triumph T20SL Tiger Cub Scrambler, 1960-1961
  • Triumph T20SS Tiger Cub Sports, 1961-1963
  • Triumph T20SH Tiger Cub Sports, 1961-1966
  • Triumph TR20 Tiger Cub Trials, 1963-1965
  • Triumph T20SC Super Cub and Bantam Cub 1966-1968

Book Excerpt: 1952-1968 Triumph Tiger Cub, Terrier, Super Cub, Bantam Cub Repair Manu

ENGINE, CLUTCH AND TRANSMISSION

REMOVING THE CYLINDER HEAD, BARREL AND PISTON
  1. The cylinder head, barrel and piston may be removed with the unit in the frame, provided the following point is noted; on machines prior to engine No: 57617 (pre-September 1959), it is necessary to remove the front and lower engine mounting bolts so that the unit can tip forwards to provide sufficient clearance.

    On later models, the holding down studs were shortened and the nuts lengthened by a similar amount, in which case the work may be undertaken without resorting to the above measures. The exhaust pipe, carburetor and rocker oil feed must first be detached in both cases.

  2. Slacken the rocker cover retaining nuts and remove the sparking plug, as these parts may prove difficult to detach at a later stage. Slacken the four cylinder head nuts using a 1/4 in. Whitworth ring spanner.

    It is not normally difficult to dislodge the cylinder head, using a hide mallet if it proves stubborn.

    Resist the temptation to pry the joint apart with a screwdriver, as this invariably results in marred or damaged cylinder head or barrel fins.

    The pushrod tube (or tunnel), and the two pushrods, will be freed as the cylinder head is lifted away. These can be removed and placed to one side.

    It is worth marking the pushrods to denote inlet and exhaust, by using a piece of insulating tape or masking tape, as it is preferable to refit these in the same position as they were before removal.

    Note that the inner item is the exhaust pushrod.

  3. The cylinder barrel may now be slid upwards off the holding down studs. Position the piston at TDC, and pack the crankcase mouth with clean rag before the piston emerges from the bore.

    This will prevent any debris from falling into the crankcase in the event of there being broken rings.


IGNITION SYSTEM
CONTACT BREAKER ASSEMBLY: ADJUSTMENT
  1. Remove the distributor cap or contact breaker cover, depending on model, and examine the faces of the contact breaker points. If they appear burnt or pitted, they should be removed for renovation or replacement. See Section 3 for details.

    If only slightly soiled, they may be dressed in place, using a magneto file or fine emery paper wrapped round a strip of thin sheet metal. Remove any accumulations of dirt using lint-free rag moistened with gas.

  2. Gradually turn the engine over until the contacts can be seen to be fully open. Check the gap, which must be between 0.014 and 0.016 in (0.35 and 0.40 mm), using a feeler gauge.

    The gauge should be a light sliding fit between the contact faces. If necessary, slacken the fixed contact retaining screw just enough to allow it to be moved.

    The desired setting can now be obtained, and the securing screw tightened, not forgetting to re-check the setting once this has been done.

    Before refitting the cover, apply a trace of grease or engine oil to the contact breaker cam.


CONTACT BREAKER ASSEMBLY: REMOVAL, EXAMINATION AND RENOVATION
  1. If the points appear badly pitted or worn, they should be removed for further examination.

    Start by disconnecting the contact breaker lead from the moving contact spring blade, making a careful note of the disposition of the washers to aid reassembly.

    Slacken and remove the fixed contact retaining screw to allow the assembly to be lifted clear of the base plate.

    The moving contact can be lifted off the fixed contact pivot pin to permit close examination of the contact faces.


Subject: 1952, 1953, 1954, 1955, 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968 Triumph Tiger Cub, Terrier, Super Cub, Bantam Cub service, maintenance, repair. ISBN-10: 085696414X | ISBN-13: 9780856964145 | Haynes 414

Specifications
  • Publisher: Haynes Manuals
  • Pages: 110 - Hundreds of b&w photos and illustrations
  • Binding: Paperback - 8.5 x 11 inches
  • ISBN: 978-0-85696-414-5
  • Years: 1952 - 1968
Table of Contents
TABLE of CONTENTS:
  • Maintenance
  • Engine
  • Clutch
  • Transmission
  • Fuel system
  • Lubrication
  • Ignition system
  • Frame
  • Forks
  • Wheels, brakes and tires
  • Electrical system
  • Wiring diagrams
Questions & Answers about Triumph Tiger Cub, Terrier Repair Shop Manual 1952-1968

Questions & Answers about Triumph Tiger Cub, Terrier Repair Shop Manual 1952-1968


Will this manual cover the 1967 Triumph T20M trials bike? If not do you have a manual for this motorcycle?
This manual does not cover the T20(M) model. Currently we do not have a manual that covers your model motorcycle. Thank you for checking with us!

Ask a question about Triumph Tiger Cub, Terrier Repair Shop Manual 1952-1968.
Customer Reviews
Triumph Tiger Cub, Terrier, Super Cub, Bantam Cub Repair Manual 1952-1968
$34.85
Free Shipping (US48)
In Stock
Close
Top
Close
Open