- GOING OUT OF PRINT - LIMITED QUANTITY -
The International Harvester Tractor Repair Manual by Clymer features easy-to-follow descriptions, step-by-step instructions, photographs, diagrams and more to make DIY tractor repairs simple. The Clymer guide is a favorite amongst home mechanics and features a level of detail that can't be found anywhere else. The easy-to-read instructions are geared towards those with less mechanical knowledge and the included wiring diagrams and photographs make executing repairs easier than ever. The International Harvester Tractor Repair Manual by Clymer covers the following models:
- International Harvester Cub 154 Lo-Boy
- International Harvester Cub 184 Lo-Boy
- International Harvester Cub 185 Lo-Boy
- Farmall Cub
- International Harvester Cub
- International Harvester Cub Lo-Boy
All International Harvester Tractor Repair Manuals ship for free to the continental 48 states. Our manuals are priced low and come backed by The Motor Bookstore's 30-day money-back guarantee. You won't find better prices, better service or a better guarantee anywhere else on the net.
Book Excerpt: International Harvester Tractor Repair Manual Cub 154 Lo-Boy, 184, 185, Farmall Cub
RandR ENGINE (All Models)
6. To remove engine, disconnect battery ground cable at battery, drain engine crankcase oil and engine coolant. Remove hood and side panels. Shut off fuel and remove fuel line from strainer to carburetor. Remove fuel tank, disconnect choke cable and remove air cleaner and pipe. Disconnect oil lines to hydraulic pump on models so equipped, and plug all openings to prevent entrance of dirt.
Remove radiator hoses and cooling fan assembly. Disconnect throttle cable from governor. Disconnect wires from generator, voltage regulator (alternator and starting motor if so equipped), positive terminal of ignition coil and headlights. Disconnect oil pressure switch. Remove side covers adjacent to engine flywheel.
Relieve pto belt tension on 154 and 185 models. Remove pto belts on 184 models. On 154 and 185 models, remove cap screws securing clutch coupling hub to flywheel.
Note: On 184 models, clutch and pressure plate may be removed with engine. Remove six cap screws holding engine in frame and lift engine from frame.
A manually actutated creeper drive is available on all models and consists of a planetary gear set, a direct drive sleeve and a spur gear.
The creeper drive is lubricated by transmission fluid and recommended lubricant is IH "Hy-Tran" hydraulic-transmission fluid. Refer to CONDENSED SPECIFICATIONS for quantity of fluid used.
68. RandR PTO CLUTCH (MODELS 154 AND 185)
To remove pto clutch, remove pto shield and support. Remove pto brake support (1-Fig. IH63) and bearing support (2). Loosen clutch cleat cap screws on left frame rail. Disconnect clutch control arm. Remove pto clutch assembly. Remove clutch housing (1-Fig.IH64) from pto drive shaft.
69.RandR PTO CLUTCH (MODEL 184)
On this model, the pto clutch must be disassembled and removed when drive shaft is removed. This procedure is outlined in paragraph 67.
70. OVERHAUL PTO CLUTCH (MODELS 154 AND 185)
With pto clutch assembly removed, loosen locking collar (Fig. IH62) and remove rear ball bearing, bearing flanges and locking collar.
NOTE: Locking collar is eccentric and tightened on shaft with a punch. Proper method of tightening is to turn collar (relative to bearing flange) in normal direction of shaft rotation. After loosening set screw, tap collar OPPOSITE the direction of shaft rotation by inserting a punch in knock hole of collar. (continued)
This I&T IH50 International Harvester Cub Tractor Repair Manual is comprehensive, concise and accurate. With the help of this manual, you can feel confident to take on any repair or service on your tractor and save money at the same time.
Subject: International Harvester farm tractor service, maintenance, repair instructions.
ISBN-10: 0872881148 | ISBN-13: 9780872881143