Subaru Brat, Impreza, Justy, Legacy, Loyale, Outback, Sedan, Std, SVX, Wagon, XT, XT-6 Repair Manual 1985-1996

SKU: CH64302-996

Subaru Brat, Impreza, Justy, Legacy, Loyale, Outback, Sedan, Std, SVX, Wagon, XT, XT-6 Repair Manual 1985-1996

SKU: CH64302-996
MSRP: $49.95
Only $42.89
free shipping (US48)

in stock | item #: CH64302-996

Adding to cart… The item has been added
Usually ships the same business day

Why Buy From Us?

  • Free Shipping
  • Veteran Owned
  • Secure Shopping
  • Satisfaction Guaranteed

Subaru Brat, Impreza, Justy, Legacy, Loyale, Outback, Sedan, Std, SVX, Wagon, XT, XT-6 Repair Manual 1985-1996

MSRP: $49.95
Only $42.89
free shipping (US48)

in stock

Adding to cart… The item has been added
This repair and workshop manual by Chilton covers 1985-1996 Subaru coupes, sedans, and wagons, U.S. and Canadian models, including:
  • Subaru Brat
  • Subaru Impreza
  • Subaru Justy
  • Subaru Legacy
  • Subaru Loyale
  • Subaru Outback
  • Subaru Sedan
  • Subaru Std
  • Subaru SVX
  • Subaru Wagon
  • Subaru XT
  • Subaru XT-6

Book Excerpt: 1985-1996 Subaru Brat, Impreza, Justy, Legacy, Loyale, Outback, Sedan, Std, SVX, Wagon, XT, XT-6 Repair Manual ENGINE AND ENGINE OVERHAUL
CRANKSHAFT PULLEY | REMOVAL AND INSTALLATION
(See Figures 102, 103 and 104)
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt(s).
  3. Using a suitable puller, remove the crankshaft pulley.
  4. Install the pulley and tighten the pulley bolt to 69-76 ft. lbs. (93-103 Nm) for 1.6L, 1.8L and 2.7L engines. Tighten the bolt on 1.2L engines to 58-72 ft. lbs. (78-98 Nm). Tighten the bolt on 2.5 engines to 94 ft. lbs. (127 Nm). Tighten the crankshaft pulley bolt on the 2.7L and 3.3L engines to 115 ft. lbs. (157 Nm).
  5. Install the accessory drive belt and adjust the tension to specification.
  6. Connect the negative battery cable.

TIMING BELT COVER AND SEAL | REMOVAL AND INSTALLATION 1.2L ENGINE (See Figure 105)
  1. Disconnect the negative battery cable.
  2. Loosen the alternator-to-engine bolts, relax the drive belt tension and remove the drive belt form the front of the engine.
  3. Using a socket wrench (through the hole in the right fender) and the Crankshaft Pulley Wrench tool No. 499205500 or equivalent, remove the crankshaft pulley-to-crankshaft bolt and the pulley from the crankshaft.
  4. Remove the rubber cover seal. Clean all mating surfaces.

BODY AND TRIM
POWER DOOR LOCKS | REMOVAL AND INSTALLATION
(See Figures 32 and 33) DOOR LOCK SWITCH
  1. Disconnect the negative battery cable.
  2. Remove the door panel retaining screws.
  3. Lift the door panel up and disconnect all the electrical connections required to separate the door panel from the door.
  4. Remove the door panel from the vehicle. Remove the switch assembly from its mounting.
  5. Installation is the reverse of the removal procedure.
DOOR LOCK ACTUATOR
  1. Disconnect the negative battery cable.
  2. Remove the door panel.
  3. Disconnect the actuator electrical connector. Disconnect the required linkage rods.
  4. Remove the actuator assembly retaining screws. Remove the actuator assembly from the vehicle.
  5. Installation is the reverse of the removal procedure.

POWER WINDOW SYSTEM | REMOVAL AND INSTALLATION REGULATOR AND MOTOR (See Figures 34, 35, 36 and 37)
  1. Remove the trim panel.
  2. Remove the remote assembly, if so equipped.
  3. Remove the sealing cover.
  4. Remove the rear view mirror from the door.
  5. Remove the outer weather strip.
  6. Remove the inner stabilizer.
  7. Loosen the upper stopper bolt from the front of door and glass stoppers and move the door glass.
  8. Remove the upper stopper from the rear of the door.
  9. Remove the bolts which hold the glass holder to the regulator slider.

Subject: 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996 Subaru Brat, Impreza, Justy, Legacy, Loyale, Outback, Sedan, Std, SVX, Wagon, XT, XT-6 service, maintenance, repair. ISBN-10: 0801987970 | ISBN-13: 9780801987977 | Chilton 64302
TABLE of CONTENTS: Introduction: About this manual | Introduction | Vehicle identification numbers | Maintenance techniques, tools and working facilities | Buying parts | Jacking and towing | Booster battery (jump) starting | Conversion factors | Automotive chemicals and lubricants | Safety first! | Troubleshooting
  • Tune-up and routine maintenance
  • Engine and overhaul procedures
  • Cooling, heating and air-conditioning systems
  • Fuel and exhaust systems
  • Engine electrical systems
  • Emissions control systems
  • Transmission
  • Brakes
  • Suspension and steering systems
  • Body
  • Chassis electrical system
  • Wiring diagrams

Specifications

  • Publisher: Chilton Manuals
  • Pages: 318 - Hundreds of b&w photos and illustrations
  • Binding: Paperback - 8.5 x 11 inches
  • ISBN: 978-0-8019-8797-7
  • Years: 1985 - 1996